Updated November 2026

When a ring video doorbell keeps ringing, the cause is usually one of a handful of things: motion settings that are too sensitive, a button that is stuck or wired incorrectly, or a chime that is reacting to a signal it should ignore. This guide walks through how to find the source of the problem and stop the false alerts without losing the doorbell alerts you actually need.

Step 1: Tell a button press from a motion event

Start by checking the Ring app’s event history. Each entry is labeled as either a press or a motion detection. If the entries say “Ding” with no motion clip, the doorbell button itself is being triggered. If they show motion events at odd hours, the problem is with the motion detector rather than the button.

Shopping for one? See our guide: Installing Ring Video Doorbell: 3 Best Models Compared (2026).

Step 2: Fix motion settings that are too sensitive

Most false rings come from motion zones that are set too broadly. Open the device settings, go to Motion Settings, and adjust the following:

  • Shrink the motion zone so it covers your porch or entry rather than the street, sidewalk or neighboring yards.
  • Lower motion sensitivity one notch at a time and test after each change.
  • Turn off motion alerts for hours when you don’t need them, using the scheduling option.
  • Disable “Motion Ding” if you only want alerts when someone presses the button.

Moving tree branches, headlights and heat from a nearby vent can all trigger motion, so check the clip before changing settings again.

Step 3: Check the doorbell button and wiring

If the button itself is causing repeated rings, the cause is often a stuck button, moisture or a wiring fault. Press the button firmly once and watch for a single event. If the chime keeps sounding after you let go, the problem is likely in the wiring or in the mechanical button.

  1. Turn off power at the breaker before touching any wiring.
  2. Check the two terminals behind the faceplate for loose screws or exposed copper touching the mounting plate.
  3. Look for water inside the button housing and seal the gap with silicone if needed.
  4. Restore power and test again.

If you are not comfortable working with live wiring, consult a licensed electrician.

Step 4: Address chime and transformer issues

Wired doorbells rely on a transformer that typically supplies 16 to 24 volts. A failing or overloaded transformer can cause a chime to sound on its own. Also check whether the chime is picking up a signal from another source, such as a second doorbell button wired to the same circuit. Our guide to Ring Video Doorbell Power Supply: Wired, Battery and Transformer Setup Guide covers how to confirm transformer output and wiring layout.

Pairings between the doorbell and an indoor chime can also be a factor. If you recently changed chimes, review the setup in Ring Video Doorbell and Chime: 5 Best Pairings for Home Alerts (2026) to make sure the chime is set to the correct tone and mode.

Step 5: Check battery and power level

Low battery can cause erratic behavior, including repeated notifications. Check the battery level in the app and replace or recharge as needed. For battery models, Top 5 Batteries for Ring Video Doorbell Options Compared (2026) lists replacement options, and Ring Video Doorbell Solar Panel: Setup, Sizing and Tips (2026) explains how to keep a battery topped up outdoors.

Common mistakes

  • Adjusting sensitivity without reviewing the clip that triggered the alert.
  • Leaving the motion zone covering a busy street.
  • Ignoring a stuck button because the doorbell still works.
  • Skipping the breaker when working on wiring.
  • Assuming a chime fault is a doorbell fault without testing each part separately.
  • A non-contact voltage tester helps confirm power is off before you touch the terminals. View on Amazon
  • Outdoor silicone sealant closes gaps around the button housing and keeps moisture out. View on Amazon

FAQ

Why does my Ring doorbell ring when no one is at the door?

The most common cause is a motion zone that picks up passing cars, pedestrians or shadows. Narrowing the zone and lowering sensitivity usually stops these alerts.

Can a wiring problem make the chime ring by itself?

Yes. A short between the button terminals or a failing transformer can keep the chime sounding. Turn off the breaker and inspect the terminals before retesting.

Will turning off motion alerts stop all false rings?

It stops motion-triggered rings, but it will not fix a stuck button or wiring fault. Test the button separately to rule those out.

Conclusion

Most cases of a ring video doorbell that keeps ringing come down to motion settings, a stuck button or a wiring or transformer issue. Work through the event history first, then adjust the motion zone, then check the hardware. Once the false alerts stop, the real visitor notifications will be much easier to trust.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our smart home guides, checking product details against manufacturer specifications and owner feedback.