Updated November 2026

If you want to know ring video doorbell how to install, the short answer is that you will remove your old doorbell (or mount onto a new bracket), connect power, attach the doorbell, and finish setup in the Ring app. Most people can complete the job in roughly an hour with basic hand tools. The exact steps depend on whether your home has existing doorbell wiring, so check that first.

Check Your Power and Wiring Before You Start

Ring video doorbells run on either hardwired power from an existing doorbell transformer or a rechargeable battery. Before buying hardware or climbing a ladder, turn off the breaker that feeds your doorbell and confirm the circuit is dead with a voltage tester. If you have no existing doorbell wiring, a battery model is the simpler route. For a deeper comparison, see How to Install a Video Doorbell: Wired and Battery Models and Wired vs Battery Video Doorbells (and Cameras).

Shopping for one? See our guide: Installing Ring Video Doorbell: 3 Best Models Compared (2026).

Mount the Bracket and Connect the Doorbell

  1. Remove your old doorbell cover and unscrew the mounting plate. Note which wire goes to which terminal, or photograph the wiring before disconnecting anything.
  2. Hold the Ring mounting bracket against the wall at the height you want, roughly 48 inches from the floor for comfortable camera framing. Use a level and mark the screw holes.
  3. Drill pilot holes if you are working on masonry, and insert wall anchors where needed. Secure the bracket firmly so it does not wobble.
  4. For hardwired installs, connect the two wires to the terminals on the back of the doorbell. Polarity does not matter for most doorbell wiring, but tight connections do.
  5. Attach the doorbell to the bracket, then restore power at the breaker.

Set the Camera Angle

Once the doorbell is attached, check the live view in the app before tightening everything down. Aim for a field of view that covers the doorstep and the approach, and avoid pointing the lens straight into a bright window or a streetlight, which causes glare.

Pair the Doorbell in the Ring App

Download the Ring app, create or sign in to your account, and select the option to set up a new device. Scan the QR code on the doorbell or enter the device details when prompted. The app will walk you through connecting to your Wi-Fi network. Most Ring models work on 2.4 GHz, so if pairing fails, check that your router broadcasts that band and that the doorbell is within reliable range.

Common Mistakes to Avoid

  • Skipping the breaker shutoff. Even low-voltage doorbell wiring can cause shorts and damage the device.
  • Mounting too high or too low, which produces poor face framing on visitors.
  • Placing the doorbell beyond your router’s reliable Wi-Fi coverage, causing dropped video.
  • Overtightening the mounting screws on the plastic housing.
  • Forgetting to update the firmware during setup, which can delay features.
  • Non-contact voltage tester: Confirms the doorbell circuit is de-energized before you touch wires. View on Amazon
  • Small bubble level: Keeps the bracket straight so the camera sits square to the door. View on Amazon
  • Wall anchors and masonry bit set: Gives a secure mount on brick or stucco. View on Amazon

FAQ

Do I need an electrician to install a Ring video doorbell?

Usually not. If you already have working doorbell wiring and feel comfortable turning off a breaker, you can handle the swap yourself. If the wiring is damaged or your panel is unfamiliar, consult a licensed electrician.

Can I install a Ring video doorbell without existing doorbell wires?

Yes. Battery-powered models mount without any wiring. You will need to recharge the battery periodically, so plan for that in your routine.

Does the doorbell need a subscription to work?

The doorbell will still ring your chime and show live view without a plan, but saved recordings and some advanced features typically require a Ring subscription. Check the current terms in the app.

Conclusion

Once you confirm your power source, mount the bracket level, connect the wires or battery, and pair the device in the Ring app, the installation is complete. Take time to set the camera angle before tightening the final screws. A careful setup now means fewer adjustments later.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our smart home guides, checking product details against manufacturer specifications and owner feedback.