Updated November 2026
A ring video doorbell wired installation diagram boils down to one simple idea: the doorbell connects to your existing doorbell wires, which carry low-voltage power from a transformer. By the end of this guide you will know which wires to expect, how to connect them, how to mount the unit, and how to confirm the doorbell is powered and working. Plan on an hour or two for most homes, and turn off power at the breaker before touching any wires.
Before You Start: Check Your Wiring
Remove your existing doorbell button and look at the wires behind it. A wired Ring setup typically uses two wires connected to the doorbell button. Ring’s wired models are designed to work with a low-voltage transformer, usually rated between 16 and 24 volts AC, which is common in most homes with a mechanical or digital chime. If your chime is wired to a transformer, you’re in good shape. If you find no wires at all, you’re likely looking at a battery model instead. For a broader comparison, see Wired vs Battery Video Doorbells (and Cameras).
Shopping for one? See our guide: Installing Ring Video Doorbell: 3 Best Models Compared (2026).
Wiring Diagram: Connecting the Two Screws
The core of any ring video doorbell wired installation diagram is simple: the two existing doorbell wires attach to the two terminal screws on the back of the Ring unit or the included mounting bracket. Polarity usually does not matter with AC doorbell circuits, so either wire can go to either screw. Tighten each screw firmly so the wire cannot pull free.
| Component | Connection |
|---|---|
| Existing doorbell wire 1 | Terminal screw 1 on Ring unit |
| Existing doorbell wire 2 | Terminal screw 2 on Ring unit |
| Transformer | Provides power through the existing wires |
| Chime (optional) | Stays connected to the same circuit |
Follow the diagram printed in your Ring installation guide, since specific terminal labels and included adapters can vary by model.
Installation Steps
- Turn off the breaker that controls your doorbell circuit, then confirm power is off by pressing the old button and checking that nothing sounds.
- Remove the old doorbell button and loosen the wires.
- Attach the mounting bracket to the wall, keeping it level and checking that the camera will have a clear view of the porch.
- Connect the two wires to the terminal screws, tightening each one.
- Slide the Ring unit onto the bracket and secure it with the included security screw.
- Restore power at the breaker and open the Ring app to complete setup and Wi-Fi connection.
Testing and Tuning Your Setup
Once the unit is connected to Wi-Fi, press the button and confirm you get a live notification and video feed. Check that your chime sounds if you kept one. If the unit reboots or the app shows low power, your wiring or transformer may be underpowered. Most Ring setup problems trace back to these basics, and the troubleshooting steps in Ring Video Doorbell Troubleshooting: 7 Fixes for Common Problems cover the most frequent ones. For a full walkthrough of setup inside the app, see Ring Video Doorbell Installation: A Step-by-Step Guide for Beginners.
Common Mistakes to Avoid
- Working on live wires. Always cut power at the breaker first.
- Assuming any two wires will work without checking for a transformer.
- Mounting the bracket crooked, which affects motion detection and camera angle.
- Leaving terminal screws loose, which can cause intermittent power loss.
- Skipping the power-supply check. If you’re unsure about your transformer’s rating, review Ring Video Doorbell Power Supply: Wired, Battery and Transformer Setup Guide.
Recommended Gear
- Non-contact voltage tester: Helps you confirm the circuit is dead before you touch any wire. View on Amazon
- Wire strippers and insulated screwdriver set: Useful for clean terminal connections on thin doorbell wire. View on Amazon
- Doorbell transformer tester: Lets you check voltage at the transformer before you commit to a wired install. View on Amazon
FAQ
Do I need a transformer for a wired Ring doorbell?
Yes, a wired Ring doorbell needs power from a low-voltage transformer, which is usually already in place if your existing doorbell works. Check that the transformer falls within the voltage range listed in Ring’s specifications.
Does wire polarity matter when connecting a Ring doorbell?
For most AC doorbell circuits, polarity does not matter, so either wire can go to either terminal. Confirm this against your model’s installation diagram before you start.
What if my doorbell has no existing wiring?
If there are no wires behind the old button, a wired model will not work without running new cable and adding a transformer. A battery or solar-powered model may be a better fit, as covered in Ring Video Doorbell Solar: Setup, Power Needs and Tips (2026).
Conclusion
A ring video doorbell wired installation diagram is mostly about confirming power, connecting two wires securely and mounting the unit level. Cut power first, check your transformer, and test the doorbell in the app before closing things up. With those steps done, your wired Ring should be ready to alert you on every visitor.

