Updated November 2026
A wyze video doorbell wired setup connects the camera directly to your existing doorbell wiring, so it runs on household power instead of a battery. This guide walks through checking your wiring, mounting the unit and confirming it works with your chime. Most homes with a working mechanical doorbell can finish the job in an afternoon.
Check Your Existing Doorbell Wiring First
Before you buy anything or remove a cover, confirm that your current doorbell is wired and powered. Press the button and listen for a chime. If the chime sounds, you likely have a low-voltage system, usually between 16 and 24 volts AC, supplied by a transformer. Wyze specifies its wired setup for this kind of low-voltage circuit, so this check decides whether the install is straightforward.
Shopping for one? See our guide: Installing Ring Video Doorbell: 3 Best Models Compared (2026).
If pressing the button does nothing, the wires may be broken, the transformer may have failed, or the doorbell may be battery-powered. A battery-only system will need a different approach, and a licensed electrician should handle any work involving line voltage.
Gather the Tools and Parts You Need
- Screwdriver (Phillips and flathead)
- Wire stripper and a multimeter or voltage tester
- Drill with masonry bit if mounting on brick or stucco
- Wall anchors and screws included with the doorbell
- Wire nuts or the connector included in the box
- Your phone with the Wyze app installed
Mount the Doorbell and Connect the Wires
Turn off power to the doorbell circuit at your breaker panel before touching any wires. Remove your old doorbell button and chime cover so you can see the two low-voltage wires. Use a voltage tester to confirm there is no live power on them.
- Attach the mounting plate to the wall, using the existing wire opening as a guide.
- Feed the two doorbell wires through the plate and strip about 1/4 inch of insulation from each end.
- Connect the wires to the terminals on the back of the doorbell unit. Polarity usually does not matter for a doorbell transformer circuit, but follow the labeling in the manual.
- Snap the doorbell onto the mounting plate and secure it with the included screws.
- Restore power at the breaker and test the button before closing everything up.
Set Up the Wyze App and Test Your Chime
Open the Wyze app, create or sign in to your account, and add the doorbell by scanning the QR code on the device. Connect it to your home Wi-Fi when prompted, and keep your phone close to the unit during pairing. Once the app shows the doorbell as online, press the button and confirm you get a live video notification on your phone.
If you want the existing mechanical chime to sound, check the compatibility notes in the app, since some chimes require a separate adapter. Owners often report that older chimes can be unreliable, so test the sound at each step rather than assuming it works.
Common Mistakes to Avoid
- Skipping the breaker shutoff, which risks shocks and damage to the transformer.
- Mounting the unit too far from Wi-Fi; test signal strength at the door before drilling.
- Using a voltage well outside the doorbell’s stated range, which can damage the unit.
- Forgetting that a wired install still needs stable Wi-Fi for live video.
- Overtightening screws on the mounting plate, which can crack older siding or brick.
For a broader overview of wiring options, see Wired vs Battery Video Doorbells (and Cameras). If you run into trouble, Wyze Video Doorbell Installation: A Step-by-Step Guide for Beginners covers additional wiring scenarios.
Recommended Gear
- A non-contact voltage tester helps you confirm the circuit is dead before you touch the wires. View on Amazon
- A doorbell wire stripper makes clean, quick work of the low-voltage conductors. View on Amazon
- A small torpedo level keeps the mounting plate straight for a tidy finish. View on Amazon
FAQ
Do I need a transformer for a wyze video doorbell wired install?
Yes, in most cases your existing doorbell transformer supplies the low-voltage power the unit needs. If your home has no transformer, you will need a different power approach, and an electrician can advise you.
Can I keep my old mechanical chime?
Often yes, but compatibility varies with the chime type. Check the Wyze app and product documentation before you rely on the old chime for alerts.
Is professional installation required?
Many homeowners can complete a low-voltage install themselves, but if you are unsure about your wiring or find line voltage, consult a licensed electrician.
Conclusion
A wired setup gives you continuous power and fewer battery trips to the door. Confirm your existing wiring, power down the circuit, and test everything in the app before you finish. With those steps done, your wyze video doorbell wired install should run reliably for years.

