Updated November 2026
To reset a Gosund smart plug, you hold the plug’s button until its indicator light changes behavior, which clears its saved Wi-Fi network and app pairing. Once it is reset, the plug returns to pairing mode and can be added again to the Smart Life or Tuya-based app you use. This guide walks through the reset, what to check beforehand, and how to recover if the plug will not reconnect.
Before You Start
A reset erases the plug’s Wi-Fi credentials and its link to your app, but it does not remove the plug from your account automatically. Confirm a few things first so the re-pairing goes smoothly.
Shopping for one? See our guide: 4 Best Lutron Outdoor Smart Plugs for Patio Lights and Decor (2026).
- Your phone is connected to a 2.4 GHz Wi-Fi network, since most Gosund plugs do not support 5 GHz.
- You know the Wi-Fi name and password, and they have not changed.
- The plug is plugged into a working outlet within easy range of your router.
- The Smart Life or Tuya Smart app is installed and you know the account you used to set the plug up.
If your router runs a combined 2.4 and 5 GHz network with the same name, the plug may fail to connect. Splitting the bands is covered in Why Smart Devices Need 2.4 GHz Wi-Fi (and How to Connect Them).
How to Factory Reset the Plug
- Plug the Gosund plug into an outlet and wait about 10 seconds for it to power up.
- Locate the small button on the front or side of the plug. Some models have a separate power button and a Wi-Fi button, so check the labeling.
- Press and hold the button for about 5 to 10 seconds, until the indicator light blinks rapidly.
- Release the button. The light should now blink slowly or in a repeating pattern, which signals pairing mode.
- If the light does not change, unplug the plug, wait 5 seconds, plug it back in, and hold the button again.
Blink patterns differ slightly between Gosund models, so consult the manual that came in the box if the pattern you see does not match these steps. The manufacturer’s specifications for your exact model are the most reliable reference.
Re-Adding the Plug After a Reset
With the plug blinking in pairing mode, open the app and tap the add-device option. Choose the smart plug category, enter your 2.4 GHz Wi-Fi password, and confirm the blinking light when the app asks. Setup usually finishes within a minute or two.
If you use the plug with a voice assistant, you may need to relink it in that assistant’s app after re-adding it to Smart Life. The general approach is covered in Smart Plug Setup and Compatibility with Voice Assistants and Apps.
Troubleshooting a Plug That Will Not Reset
Owners often report that a plug resets fine but fails to connect to the network. Check the following before assuming the plug is faulty.
| Symptom | Likely cause | Fix |
|---|---|---|
| Light never changes when held | Button not fully pressed or power issue | Unplug, wait, replug, hold 10 seconds |
| App cannot find the device | Phone on 5 GHz network | Switch phone to 2.4 GHz and retry |
| Connects, then drops offline | Weak signal at outlet | Move plug closer to router or use a mesh node |
| Plug still shows in old account | Previous pairing not removed | Delete the old device entry in the app |
Common Mistakes and Tips
- Holding the button for only a second or two, which usually triggers nothing.
- Forgetting to delete the old device entry, which can cause duplicate or stuck listings.
- Entering the wrong Wi-Fi password, which is the most frequent cause of failed pairing.
- Resetting a plug that is controlling something important without first turning that load off.
Recommended Gear
- Smart Life compatible Wi-Fi smart plug: A replacement Gosund-style plug is useful if the original will not reset after several attempts. View on Amazon
- Outlet tester: Confirms the outlet is live before you blame the plug for failing to power up. View on Amazon
FAQ
Will resetting the plug delete my schedules?
Yes. A factory reset clears the plug’s stored settings, including schedules and automations, so you will need to recreate them after re-adding the device.
How long should I hold the button?
Most owners hold it for about 5 to 10 seconds until the light blinks rapidly. Confirm the pattern against your model’s manual.
Can I reset the plug without the app?
Yes, the physical button reset works on its own. You will still need the app to pair the plug to your Wi-Fi network afterward.
Conclusion
Resetting a Gosund smart plug takes only a few minutes once you hold the button long enough to enter pairing mode. Keep your phone on 2.4 GHz Wi-Fi, delete the old device entry, and re-add the plug in your app. If it still fails, check signal strength and the blink pattern in your manual.

